ROM VER: 2.1.0 CFG 0a B . . Result: PASS U-Boot 2010.06-LANTIQ-v-2.3.148 =1-0-9-1= (Aug 17 2018 - 17:34:46) interAptiv cps cpu/ddr run in 600/666 Mhz DRAM: 224 MiB NAND: ONFI flash detected ONFI param page 0 valid NAND device: Manufacturer ID: 0xc2, Chip ID: 0xf1 (MXIC MX30LF1G18AC) 128 MiB Bad block table found at page 65472, version 0x01 Bad block table found at page 65408, version 0x01 nand_read_bbt: Bad block at 0x000007220000 In: serial Out: serial Err: serial Net: multi type Internal phy firmware version: 0x8547 GRX500 Switch Creating 1 MTD partitions on "nand0": 0x0000002c0000-0x000007cc0000 : "mtd=5" UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 126976 bytes UBI: smallest flash I/O unit: 2048 UBI: VID header offset: 2048 (aligned 2048) UBI: data offset: 4096 UBI: attached mtd1 to ubi0 UBI: MTD device name: "mtd=5" UBI: MTD device size: 122 MiB UBI: number of good PEBs: 975 UBI: number of bad PEBs: 1 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 5 UBI: available PEBs: 542 UBI: total number of reserved PEBs: 433 UBI: number of PEBs reserved for bad PEB handling: 9 UBI: max/mean erase counter: 44/22 Volume bootcoreA found at volume id 4 read 0 bytes from volume 4 to a03fffc0(buf address) Read [2285568] bytes Volume kernelA found at volume id 0 read 0 bytes from volume 0 to a07fffc0(buf address) Read [8634368] bytes ## Booting kernel from Legacy Image at 80800000 ... Image Name: MIPS LEDE Linux-4.9 Created: 2020-07-28 13:28:55 UTC Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 2064320 Bytes = 2 MiB Load Address: a2020000 Entry Point: a2020400 Verifying Checksum ... OK Uncompressing Kernel Image ... OK Starting kernel ... [ 0.000000] Linux version 4.9.109 (buildbot@buildhost) (gcc version 6.3.0 (LEDE GCC 6.3.0 17.01.4_intel) ) #0 SMP Tue Jul 28 13:26:48 UTC 2020 [ 0.000000] SoC: GRX350 rev 1.2 [ 0.000000] CPU0 revision is: 0001a120 (MIPS interAptiv (multi)) [ 0.000000] Enhanced Virtual Addressing (EVA 1GB) activated [ 0.000000] MIPS: machine is Netcomm NDD-0300 [ 0.000000] Coherence Manager IOCU detected [ 0.000000] Hardware DMA cache coherency disabled [ 0.000000] earlycon: lantiq0 at MMIO 0x16600000 (options '') [ 0.000000] bootconsole [lantiq0] enabled [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 0e000000 @ 20000000 (usable) [ 0.000000] memory: 00006a1d @ 226d2480 (reserved) [ 0.000000] Initial ramdisk at: 0x609f8000 (6520832 bytes) [ 0.000000] cma: Reserved 32 MiB at 0x2c000000 [ 0.000000] SMPCMP: CPU0: cmp_smp_setup [ 0.000000] VPE topology {2,2} total 4 [ 0.000000] Detected 3 available secondary CPU(s) [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] MIPS secondary cache 128kB, 4-way, linesize 32 bytes. [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000020000000-0x0000000027ffffff] [ 0.000000] Normal [mem 0x0000000028000000-0x000000002dffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000020000000-0x000000002dffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000020000000-0x000000002dffffff] [ 0.000000] percpu: Embedded 12 pages/cpu @681dc000 s17536 r8192 d23424 u49152 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 56896 [ 0.000000] Kernel command line: earlycon=lantiq,0x16600000 nr_cpus=4 nocoherentio clk_ignore_unused root=/dev/ram ro rd_start=0x609f8000 rd_size=6520832 ubi.mtd=system_sw do_overlay console=ttyLTQ0,115200 ethaddr=F8:CA:59:8B:C4:1D panic=1 mtdparts=17c00000.nand-parts:1m(uboot),256k(ubootconfigA),256k(ubootconfigB),256k(gphyfirmware),1m(calibration),122m(system_sw),-(res) init=/etc/preinit active_bank=A update_chk=0 maxcpus=4 pci=pcie_bus_perf ethwan= ubootver=U-Boot-2010.06-LANTIQ-v-2.3.148 =1-0-9-1= [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 151348K/229376K available (5025K kernel code, 341K rwdata, 1256K rodata, 1300K init, 2106K bss, 45260K reserved, 32768K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:527 [ 0.000000] EIC is off [ 0.000000] VINT is on [ 0.000000] CPU Clock: 600000000Hz mips_hpt_frequency 300000000Hz [ 0.000000] clocksource: gptc: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000012] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.008336] Calibrating delay loop... 398.13 BogoMIPS (lpj=1990656) [ 0.069327] pid_max: default: 32768 minimum: 301 [ 0.074111] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.080546] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.089010] CCA is coherent, multi-core is fine [ 0.092111] MAXCORE = 2, MAXCPU = 4, MAXTCS = 6 MAX_VPE = 2 [ 0.097655] [vmb_cpu_active]:[308], cpu = 0 [ 0.101935] [update_DB_from_DT]:[371], cpuid = 0 name = LINUX [ 0.107550] [update_DB_from_DT]:[371], cpuid = 1 name = LINUX [ 0.113434] [update_DB_from_DT]:[371], cpuid = 2 name = LINUX [ 0.119068] [update_DB_from_DT]:[371], cpuid = 3 name = MPEFW [ 0.124835] [vmb_check_IBL_fw_msg]:[333] vpet[j].bl_status = 2, cpu = 1 [ 0.131361] [vmb_check_IBL_fw_msg]:[333] vpet[j].bl_status = 2, cpu = 2 [ 0.137924] [vmb_check_IBL_fw_msg]:[333] vpet[j].bl_status = 2, cpu = 3 [ 0.144541] [ 0.144541] Initial ITC_Address_Map0 00000000 [ 0.150354] def ITC_Address_Map1 01200000[ 0.154329] [ 0.154329] new ITC_Address_Map1 0120fc00 def ITC_Address_Map0 00000000[ 0.162488] [ 0.162488] new ITC_Address_Map0 1c300001 [ 0.167957] [ 0.167957] ITC Init done on Core 0 on CPU 0 !!! [ 0.176957] [vmb_cpu_alloc]:[688] CPU vpet.cpu_status = 11 [ 0.181115] [vmb_cpu_start]:[951] vmb_fw_msg_t = a00000b8 cpu = 1 ! [ 0.187231] [vmb_cpu_start]:[966] start_address = 2723152972 cpu = 1 !!!! [ 0.194108] [gic_trigger]:[635] VMB_CPU_IPI1 - 20 CPU = 1 tsi1e W8IT got IPI intarru:t t1 launch frFm cRu P1N pSG_>D w 0wakeup_vpe = 0 ! [ 0.205609] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.205619] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.205632] MIPS secondary cache 128kB, 4-way, linesize 32 bytes. [ 0.205788] [ 0.205788] Initial ITC_Address_Map0 1c300001 [ 0.205806] ITC Memory is already initialised for Core 0 at address 1c300000 !!! [ 0.205807] CPU1 revision is: 0001a120 (MIPS interAptiv (multi)) [ 0.388102] [vmb_cpu_active]:[308], cpu = 1 [ 0.388194] [vmb_cpu_start]:[1000] OUTSIDE wakeup_vpe = 1 vpet->fw_vmb.status = 1 [ 0.398398] [vmb_cpu_start]:[1006] ret = 1 [ 0.403417] [vmb_cpu_alloc]:[688] CPU vpet.cpu_status = 11 [ 0.407924] [vmb_cpu_start]:[951] vmb_fw_msg_t = a0000168 cpu = 2 ! [ 0.414238] [vmb_cpu_start]:[966] start_address = 2723152972 cpu = 2 !!!! [ 0.421042] [gic_trigger]:[640] VMB_CPU_IPI2 - 21 CPU = 2 [ 0.426405] got _PI intartupt to] WAITh from cRESPON Met->v_w 01akeup_vpe = 0 ! [ 0.432551] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.432562] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.432575] MIPS secondary cache 128kB, 4-way, linesize 32 bytes. [ 0.432705] [ 0.432705] Initial ITC_Address_Map0 00000000 [ 0.432717] [ 0.432717] def ITC_Address_Map1 01200000 [ 0.432722] [ 0.432722] new ITC_Address_Map1 0120fc00 [ 0.432727] [ 0.432727] def ITC_Address_Map0 00000000 [ 0.432735] [ 0.432735] new ITC_Address_Map0 1c300001 [ 0.432736] [ 0.432736] ITC Init done on Core 1 on CPU 2 !!! [ 0.432743] CPU2 revision is: 0001a120 (MIPS interAptiv (multi)) [ 0.535683] [vmb_cpu_active]:[308], cpu = 2 [ 0.535779] [vmb_cpu_start]:[1000] OUTSIDE wakeup_vpe = 1 vpet->fw_vmb.status = 1 [ 0.545959] [vmb_cpu_start]:[1006] ret = 1 [ 0.550277] Brought up 3 CPUs [ 0.564452] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.572938] futex hash table entries: 1024 (order: 3, 32768 bytes) [ 0.581801] pinctrl core: initialized pinctrl subsystem [ 0.587007] NET: Registered protocol family 16 [ 0.590167] XRX500 GPIO Driver, (C) 2014 Lantiq Deutschland Gmbh [ 0.601069] dma-grx500 1e300000.dma: dma3 base address be300000 chained_irq 29 irq_base 30 [ 0.610428] dma-grx500 1e300000.dma: Init done - rev: a, ports: 1, channels: 64 [ 0.620405] dma-grx500 1c100000.dma: dma2tx base address bc100000 chained_irq 103 irq_base 104 [ 0.628431] dma-grx500 1c100000.dma: Init done - rev: a, ports: 1, channels: 16 [ 0.635787] dma-grx500 1c200000.dma: dma2rx base address bc200000 chained_irq 120 irq_base 121 [ 0.644820] dma-grx500 1c200000.dma: Init done - rev: a, ports: 1, channels: 32 [ 0.652247] dma-grx500 1a100000.dma: dma1tx base address ba100000 chained_irq 153 irq_base 154 [ 0.660191] dma-grx500 1a100000.dma: Init done - rev: a, ports: 1, channels: 16 [ 0.667572] dma-grx500 1a200000.dma: dma1rx base address ba200000 chained_irq 170 irq_base 171 [ 0.675949] dma-grx500 1a200000.dma: Init done - rev: a, ports: 1, channels: 12 [ 0.686471] intel-reset-syscon 16000000.reset-controller: Reset cause: 18 [ 0.697360] dma0-grx500 16e00000.dma: base address b6e00000 chained_irq 206 irq_base 207 [ 0.704129] dma0-grx500 16e00000.dma: Init done - hw rev: A, ports: 4, channels: 16 [ 0.712103] intel-pinctrl 16c80000.pinctrl: pinbank id: 0, reg: 0xb6c80000, pinbase: 0, pin number: 32, pinmap: 0xf1efefff [ 0.722803] intel-pinctrl 16c80000.pinctrl: pinbank id: 1, reg: 0xb6c80100, pinbase: 32, pin number: 32, pinmap: 0x3bff0c1f [ 0.734073] intel-pinctrl 16c80000.pinctrl: Total 13 groups, 13 functions [ 0.740885] intel-pinctrl 16c80000.pinctrl: gpiochip membase: 0xb6c00000 [ 0.747817] intel-pinctrl 16c80000.pinctrl: gpiochip membase: 0xb6c00100 [ 0.798588] cqm_platdev_init is called [ 0.800884] dev falcon-cqm [ 0.803569] [parse_dts] .. [30] [ 0.806786] Unable to get node cqm for falcon-cqm [ 0.811480] add_cqm_dev(#116): parse_dts fail for falcon-cqm [ 0.817023] dev grx500-cbm [ 0.819751] [parse_dts] .. [30] [ 0.822963] num_res 12 [ 0.825233] intr 94 [ 0.827278] intr 95 [ 0.829404] intr 96 [ 0.831445] intr 97 [ 0.833528] intr 98 [ 0.835607] intr 0 [ 0.837598] No rcu reset for cbm [ 0.840891] No syscon phandle specified for wan mux [ 0.845669] parse dts done [ 0.848386] adding resources [ 0.851226] resources added [ 0.854264] Successfully Registered Platform device grx500-cbm. [ 0.860054] device added [ 0.936029] [cbm] { cbm_xrx500_probe : 5264 }reserving 18874368 bytes @ 6c000000 for CBM [ 0.975498] [cbm] { cbm_xrx500_probe : 5274 }reserving 8388608 bytes @ 6d200000 for CBM [ 0.982125] [cbm] { cbm_xrx500_probe : 5279 }94 irq [ 0.987064] [cbm] { cbm_xrx500_probe : 5302 }2 [ 0.991468] [drv_tmu_ll] { get_cbm_clock : 7794 }CBM Clock: 200000000Hz=200MHZ [ 0.998683] Initializing TMU with Base Address=be700000: ... [ 1.008321] TMU Initialization Done [ 1.010338] 0x6c000000 0x1200000 0x800 [ 1.014065] 0x6c000000 0x1200000 [ 1.017277] 0x6d200000 0x800000 0x4000 [ 1.021048] 0x6d200000 0x800000 [ 1.024675] [cbm] { init_fsqm_buf_std : 812 }init fsqm std successfully [ 1.030781] [cbm] { init_fsqm_buf_jumbo : 854 }init fsqm jbo successfully [ 1.037502] [cbm] { init_fsqm : 877 }fsqm init successfully [ 1.043089] [cbm] { init_cbm_basic : 912 }PHY ADDR STD 0x2c000000 [ 1.049156] [cbm] { init_cbm_basic : 913 }PHY ADDR JBO 0x2d200000 [ 1.055450] [cbm] { init_cbm_basic : 931 }init basic CBM successfully [ 1.061676] [cbm] { cbm_hw_init : 1811 }CBM HW init [ 1.066633] [cbm] { setup_DMA_p2p : 4711 }setup_DMA_p2p executed [ 1.072515] [cbm] { reserved_ports_highest : 4770 }2 2 19 35 [ 1.078162] [cbm] { init_cbm_dqm_cpu_port : 1075 }2 [ 1.083026] [cbm] { assign_port_from_DT : 456 }0x0 2 [ 1.087936] [cbm] { assign_port_from_DT : 456 }0x20 2 [ 1.093309] [cbm] { cbm_add_to_list : 250 }1 [ 1.097228] [cbm] { reserved_ports_highest : 4770 }1 1 18 34 [ 1.102887] [cbm] { init_cbm_dqm_cpu_port : 1075 }1 [ 1.107746] [cbm] { assign_port_from_DT : 456 }0x80 1 [ 1.112799] [cbm] { reserved_ports_highest : 4770 }3 3 20 36 [ 1.118424] [cbm] { init_cbm_dqm_cpu_port : 1075 }3 [ 1.123283] [cbm] { assign_port_from_DT : 456 }0x2000000 3 [ 1.128766] [cbm] { cbm_add_to_list : 250 }1 [ 1.132991] [cbm] { reserved_ports_highest : 4770 }6 6 0 16 [ 1.138091] random: fast init done [ 1.141931] [cbm] { dma_port_enable : 4244 }6 0x4 [ 1.146637] [cbm] { reserved_ports_highest : 4770 }7 7 1 17 [ 1.152203] [cbm] { dma_port_enable : 4244 }7 0x4 [ 1.156877] [cbm] { reserved_ports_highest : 4770 }8 8 2 18 [ 1.162436] [cbm] { dma_port_enable : 4244 }8 0x4 [ 1.167117] [cbm] { reserved_ports_highest : 4770 }9 9 3 19 [ 1.172688] [cbm] { dma_port_enable : 4244 }9 0x4 [ 1.177363] [cbm] { reserved_ports_highest : 4770 }10 10 4 20 [ 1.183095] [cbm] { dma_port_enable : 4244 }10 0x4 [ 1.187863] [cbm] { reserved_ports_highest : 4770 }11 11 5 21 [ 1.193608] [cbm] { dma_port_enable : 4244 }11 0x4 [ 1.198399] [cbm] { reserved_ports_highest : 4770 }12 12 6 22 [ 1.204077] [cbm] { dma_port_enable : 4244 }12 0x4 [ 1.208912] [cbm] { reserved_ports_highest : 4770 }13 13 7 23 [ 1.214580] [cbm] { dma_port_enable : 4244 }13 0x4 [ 1.219397] [cbm] { reserved_ports_highest : 4770 }14 14 8 24 [ 1.225083] [cbm] { dma_port_enable : 4244 }14 0x4 [ 1.229911] [cbm] { reserved_ports_highest : 4770 }15 15 9 25 [ 1.235587] [cbm] { dma_port_enable : 4244 }15 0x4 [ 1.240403] [cbm] { reserved_ports_highest : 4770 }16 16 10 26 [ 1.246176] [cbm] { dma_port_enable : 4244 }16 0x4 [ 1.251004] [cbm] { reserved_ports_highest : 4770 }17 17 11 27 [ 1.256767] [cbm] { dma_port_enable : 4244 }17 0x4 [ 1.261583] [cbm] { reserved_ports_highest : 4770 }18 18 -16 0 [ 1.267356] [cbm] { dma_port_enable : 4244 }18 0x4 [ 1.272209] [cbm] { reserved_ports_highest : 4770 }19 19 12 28 [ 1.277946] [cbm] { dma_port_enable : 4244 }19 0x4 [ 1.282764] [cbm] { reserved_ports_highest : 4770 }20 20 13 29 [ 1.288569] [cbm] { dma_port_enable : 4244 }20 0x4 [ 1.293329] [cbm] { init_special_ports : 4777 }20 [ 1.297998] [cbm] { cbm_add_to_list : 250 }1 [ 1.302278] [cbm] { reserved_ports_highest : 4770 }21 21 14 30 [ 1.308091] [cbm] { dma_port_enable : 4244 }21 0x4 [ 1.312862] [cbm] { init_special_ports : 4777 }21 [ 1.317528] [cbm] { cbm_add_to_list : 250 }1 [ 1.321812] [cbm] { reserved_ports_highest : 4770 }22 22 25 41 [ 1.327598] [cbm] { dma_port_enable : 4244 }22 0x4 [ 1.332414] [cbm] { reserved_ports_highest : 4770 }23 23 15 31 [ 1.338221] [cbm] { init_cbm_dqm_ldma_port : 1108 }23 [ 1.343244] [cbm] { reserved_ports_highest : 4770 }5 5 21 37 [ 1.348889] [cbm] { init_cbm_dqm_scpu_port : 1089 }5 [ 1.354141] [cbm] { reserved_ports_highest : 4770 }4 4 16 32 [ 1.359492] [cbm] { init_cbm_dqm_cpu_port : 1075 }4 [ 1.364334] [cbm] { assign_port_from_DT : 456 }0x8 4 [ 1.369291] [cbm] { reserved_ports_highest : 4770 }24 24 22 38 [ 1.375077] [cbm] { init_cbm_dqm_cpu_port : 1075 }24 [ 1.380075] [cbm] { assign_port_from_DT : 456 }0x8 24 [ 1.385065] [cbm] { reserved_ports_highest : 4770 }25 25 23 39 [ 1.390900] [cbm] { init_cbm_dqm_cpu_port : 1075 }25 [ 1.395841] [cbm] { assign_port_from_DT : 456 }0x8 25 [ 1.400905] [cbm] { reserved_ports_highest : 4770 }26 26 24 40 [ 1.406674] [cbm] { init_cbm_dqm_cpu_port : 1075 }26 [ 1.411663] [cbm] { assign_port_from_DT : 456 }0x8 26 [ 1.416658] [cbm] { init_cbm_eqm_cpu_port : 938 }0 [ 1.421463] [cbm] { init_cbm_eqm_cpu_port : 938 }1 [ 1.426204] [cbm] { init_cbm_eqm_cpu_port : 938 }2 [ 1.431000] [cbm] { init_cbm_eqm_cpu_port : 938 }3 [ 1.435755] [cbm] { dma_port_enable : 4244 }5 0x1 [ 1.440478] [cbm] { dma_port_enable : 4244 }5 0x2 [ 1.445129] [cbm] { dma_port_enable : 4244 }6 0x1 [ 1.449839] [cbm] { dma_port_enable : 4244 }6 0x2 [ 1.454504] [cbm] { dma_port_enable : 4244 }7 0x1 [ 1.459222] [cbm] { dma_port_enable : 4244 }7 0x2 [ 1.463878] [cbm] { dma_port_enable : 4244 }8 0x1 [ 1.468589] [cbm] { dma_port_enable : 4244 }8 0x2 [ 1.473253] [cbm] { dma_toe_port_enable : 4271 }9 0x1 [ 1.478320] [cbm] { dma_vrx318_port_enable : 4284 }15 0x1 [ 1.483678] [cbm] { init_cbm_dqm_cpu_port : 1075 }0 [ 1.488552] [cbm] { init_cbm_dqm_cpu_port : 1075 }1 [ 1.493389] [cbm] { init_cbm_dqm_cpu_port : 1075 }2 [ 1.498282] Load spreader init successfully [ 1.502587] [cbm] { cbm_xrx500_probe : 5358 }CBM Clock: 200000000Hz [ 1.508704] [cbm] { cbm_xrx500_probe : 5360 }EQM delay Enabled [ 1.514486] [cbm] { igp_delay_set : 4371 }port0 delay16 [ 1.519725] [cbm] { igp_delay_set : 4371 }port1 delay16 [ 1.524899] [cbm] { igp_delay_set : 4371 }port2 delay16 [ 1.530129] [cbm] { igp_delay_set : 4371 }port3 delay16 [ 1.535316] [cbm] { igp_delay_set : 4371 }port4 delay16 [ 1.540554] [cbm] { igp_delay_set : 4371 }port5 delay16 [ 1.545732] [cbm] { igp_delay_set : 4371 }port6 delay16 [ 1.550961] [cbm] { igp_delay_set : 4371 }port7 delay16 [ 1.556148] [cbm] { igp_delay_set : 4371 }port8 delay16 [ 1.561386] [cbm] { igp_delay_set : 4371 }port9 delay16 [ 1.566565] [cbm] { igp_delay_set : 4371 }port10 delay16 [ 1.571881] [cbm] { igp_delay_set : 4371 }port11 delay16 [ 1.577155] [cbm] { igp_delay_set : 4371 }port12 delay16 [ 1.582479] [cbm] { igp_delay_set : 4371 }port13 delay16 [ 1.587745] [cbm] { igp_delay_set : 4371 }port14 delay16 [ 1.593061] [cbm] { igp_delay_set : 4371 }port15 delay16 [ 1.598377] [cbm] { dequeue_dma_port_init : 4207 }6 0x0 2 1 [ 1.603908] [cbm] { dequeue_dma_port_init : 4207 }7 0x0 2 2 [ 1.609476] [cbm] { dequeue_dma_port_init : 4207 }8 0x0 2 3 [ 1.615006] [cbm] { dequeue_dma_port_init : 4207 }9 0x0 2 4 [ 1.620598] [cbm] { dequeue_dma_port_init : 4207 }10 0x0 2 5 [ 1.626204] [cbm] { dequeue_dma_port_init : 4207 }11 0x0 2 6 [ 1.631871] [cbm] { dequeue_dma_port_init : 4207 }12 0x0 2 9 [ 1.637490] [cbm] { dequeue_dma_port_init : 4207 }13 0x0 2 10 [ 1.643253] [cbm] { dequeue_dma_port_init : 4207 }14 0x0 2 11 [ 1.648972] [cbm] { dequeue_dma_port_init : 4207 }15 0x0 2 12 [ 1.654676] [cbm] { dequeue_dma_port_init : 4207 }16 0x0 2 13 [ 1.660440] [cbm] { dequeue_dma_port_init : 4207 }17 0x0 2 14 [ 1.666135] [cbm] { dequeue_dma_port_init : 4207 }18 0x0 1 13 [ 1.671891] [cbm] { dequeue_dma_port_init : 4207 }19 0x0 1 15 [ 1.677593] [cbm] { dequeue_dma_port_init : 4207 }20 0x0 1 5 [ 1.683268] [cbm] { dequeue_dma_port_init : 4207 }21 0x0 1 6 [ 1.688901] [cbm] { dequeue_dma_port_init : 4207 }22 0x0 1 11 [ 1.694617] [cbm] { enqueue_dma_port_init : 4149 }5 0x2 2 0 30 [ 1.700468] [cbm] { enqueue_dma_port_init : 4149 }5 0x1 2 14 0 [ 1.706238] [cbm] { enqueue_dma_port_init : 4149 }6 0x2 2 0 31 [ 1.712080] [cbm] { enqueue_dma_port_init : 4149 }6 0x1 2 15 0 [ 1.717869] [cbm] { enqueue_dma_port_init : 4149 }7 0x2 1 0 6 [ 1.723634] [cbm] { enqueue_dma_port_init : 4149 }7 0x1 1 0 0 [ 1.729350] [cbm] { enqueue_dma_port_init : 4149 }8 0x2 1 0 11 [ 1.735144] [cbm] { enqueue_dma_port_init : 4149 }8 0x1 1 5 0 [ 1.740903] [cbm] { cbm_xrx500_probe : 5414 }CBM: Init Done !![ 1.791861] try to register spd_mon driver [ 1.794769] spdmon 16080110.speedm: base address: 0xb6080110 [ 1.800333] spdmon 16080110.speedm: PHY base address: 0x16080110 [ 1.806225] device number :253 [ 1.809957] spdmon 16080110.speedm: spd_mon driver : init done !! [ 1.818163] spd_mon driver registered [ 1.822532] clocksource: Switched to clocksource gptc [ 1.829138] NET: Registered protocol family 2 [ 1.833386] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 1.839033] TCP bind hash table entries: 2048 (order: 2, 16384 bytes) [ 1.845553] TCP: Hash tables configured (established 2048 bind 2048) [ 1.851884] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 1.857691] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 1.864265] NET: Registered protocol family 1 [ 1.869747] Trying to unpack rootfs image as initramfs... [ 1.875279] rootfs image is not initramfs (junk in compressed archive); looks like an initrd [ 1.979149] Freeing initrd memory: 6368K [ 1.984816] workingset: timestamp_bits=30 max_order=16 bucket_order=0 [ 2.002225] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 2.006673] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 2.020785] io scheduler noop registered [ 2.023327] io scheduler deadline registered (default) [ 2.029186] intel-pcie-slim-phy 18a00000.pciephy: PCIe slim phy[2] init success! [ 2.152503] OF: PCI: host bridge /pcie@18e00000 ranges: [ 2.156310] OF: PCI: MEM 0xbc000000..0xbeffffff -> 0xbc000000 [ 2.162186] OF: PCI: IO 0xbf800000..0xbf80ffff -> 0xbf800000 [ 2.170328] intel-pcie-slim-phy 18a00000.pciephy: PCIe LCPLL SSC Mode Enabled [ 2.306683] intel-pcie 18e00000.pcie: PCI host bridge to bus 0002:00 [ 2.311595] pci_bus 0002:00: root bus resource [bus 00-08] [ 2.317114] pci_bus 0002:00: root bus resource [mem 0xbc000000-0xbeffffff] [ 2.323929] pci_bus 0002:00: root bus resource [io 0xbf800000-0xbf80ffff] [ 2.331357] pci 0002:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 2.339753] pci 0002:00:00.0: PCI bridge to [bus 01-08] [ 2.344352] pci 0002:00:00.0: BAR 8: assigned [mem 0xbc000000-0xbc7fffff] [ 2.350726] pci 0002:00:00.0: BAR 9: assigned [mem 0xbc800000-0xbc8fffff pref] [ 2.357980] pci 0002:00:00.0: BAR 7: assigned [io 0xbf800000-0xbf800fff] [ 2.364736] pci 0002:01:00.0: BAR 0: assigned [mem 0xbc000000-0xbc7fffff] [ 2.371477] pci 0002:00:00.0: PCI bridge to [bus 01] [ 2.376461] pci 0002:00:00.0: bridge window [io 0xbf800000-0xbf800fff] [ 2.383217] pci 0002:00:00.0: bridge window [mem 0xbc000000-0xbc7fffff] [ 2.389958] pci 0002:00:00.0: bridge window [mem 0xbc800000-0xbc8fffff pref] [ 2.397223] pci 0002:00:00.0: Max Payload Size set to 256/ 256 (was 128), Max Read Rq 256 [ 2.405630] pci 0002:01:00.0: Max Payload Size set to 128/ 128 (was 128), Max Read Rq 128 [ 2.414135] intel-pcie 18e00000.pcie: Intel AXI PCIe Root Complex Port 2 Init Done [ 2.424402] [mips_tc_init] dma_zalloc_coherent dev->name=(null) sizeof(struct mips_tc_sg_mem)=1680 shared_phy_mem=27c0c000 [ 2.434057] [mips_tc_init] dma_zalloc_coherent shared_vir_uncached_mem=a7c0c000 shared_vir_cached_mem=67c0c000 shared_working_vir_mem=67c0c000 [ 2.447105] =MIPS TC Shared memory: a7c0c000 67c0c000 67c0c000 | Data: a7c10000 [ 2.454198] [vmb_tc_alloc]:[1046] CPU tct tc_status = 1 [ 2.459248] UMT initialize success on processor: 1 ! [ 2.464219] HW MCPY driver: Version: 1.1.0, Init Done! [ 2.470362] 16600000.serial: ttyLTQ0 at MMIO 0x16600000 (irq = 195, base_baud = 0) is a lantiq,asc [ 2.487994] console [ttyLTQ0] enabled [ 2.487994] console [ttyLTQ0] enabled [ 2.493872] bootconsole [lantiq0] disabled [ 2.493872] bootconsole [lantiq0] disabled [ 2.502729] 16700000.serial: ttyLTQ1 at MMIO 0x16700000 (irq = 198, base_baud = 0) is a lantiq,asc [ 2.511566] Lantiq MIPSInterAptiv MPS driver, version 1.0.0.0, (c) 2006-2013 Lantiq Deutschland GmbH [ 2.520850] MPS: major Id 250 [ 2.523249] Major Id is 249 [ 2.525769] ICC driver registered [ 2.529403] sysrst_init: Trying to register System Reset Driver ... [ 2.535802] sysrst_pre_init: Detect InterAptiv CPU ... [ 2.540807] sysrst_init: Lantiq CPE GRX500 System driver version 1.0.0 [ 2.547010] sysrst_init: GRX500 System Reset initialized successfully! [ 2.555446] brd: module loaded [ 2.558801] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xf1 [ 2.563757] nand: Macronix MX30LF1G18AC [ 2.567512] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 2.578348] Scanning device for bad blocks [ 2.688337] Bad eraseblock 913 at 0x000007220000 [ 2.704510] 7 cmdlinepart partitions found on MTD device 17c00000.nand-parts [ 2.710085] Creating 7 MTD partitions on "17c00000.nand-parts": [ 2.716046] 0x000000000000-0x000000100000 : "uboot" [ 2.722869] 0x000000100000-0x000000140000 : "ubootconfigA" [ 2.728659] 0x000000140000-0x000000180000 : "ubootconfigB" [ 2.734551] 0x000000180000-0x0000001c0000 : "gphyfirmware" [ 2.740332] 0x0000001c0000-0x0000002c0000 : "calibration" [ 2.746151] 0x0000002c0000-0x000007cc0000 : "system_sw" [ 2.753695] 0x000007cc0000-0x000008000000 : "res" [ 2.760870] Lantiq SoC SPI controller rev 9 (TXFS 32, RXFS 32, DMA 1) [ 2.767010] libphy: Fixed MDIO Bus: probed [ 2.770840] Node name /ssx1@1c000000/gswitch@000000 [ 2.776551] Node name /ssx2@1a000000/gswitch@000000 [ 2.782007] ::::::: SWAPI Reached :::::: [ 2.784613] GSWIP devid = 0 [ 2.787335] memres->start = 0x1c000000 memres->end = 0x1c002fff [ 2.793395] addr_gswl = 0xbc000000 [ 2.796627] drivers/net/ethernet/lantiq/switch-api/gsw_init.c:ltq_gsw_api_register:952 (Register l base:0xbc000000) [ 2.807091] SWAPI: Registered char device [switch_api] with major no [81] [ 2.813854] addr_gswl = 0xbc000000 [ 2.817195] [ 2.817195] ########## Switch Core INIT for device = 0 ########## [ 2.824772] Switch Core Base Address = 0xbc000000 [ 2.829446] [ 2.829446] GSWIP 3.0 HardWare Capability [ 2.834928] ----------------------------- [ 2.834928] [ 2.840372] Switch Version ID = 0x30 [ 2.845338] [ 2.846795] Number of logical port = 7 [ 2.851482] Number of ports including V port = 8 [ 2.856199] Number of queues = 32 [ 2.860945] Number of meter instance = 16 [ 2.865741] Number of shapers = 32 [ 2.870494] Number of PMAC = 1 [ 2.875213] Number of CPU PORT = 0 [ 2.879867] [ 2.881345] PPPOE table size = 16 [ 2.886141] IP packet length table size = 16 [ 2.890894] Protocol table size = 32 [ 2.895698] MAC DA/SA table size = 64 [ 2.900443] Application table size = 64 [ 2.905238] IP DA/SA MSB table size = 64 [ 2.909991] IP DA/SA LSB table size = 64 [ 2.914794] Multicast table size = 64 [ 2.919540] Multicast Hw Snoop = 0 [ 2.924249] TFLOW table size = 64 [ 2.929003] MAC bridge table size = 2048 [ 2.933980] TFLOW RMON counter table Size = 256 [ 2.938812] Payload Table Size = 64 [ 2.943608] Extend VLAN Table Size table = 0 [ 2.948274] VlanFilter table Size = 0 [ 2.948274] [ 2.954471] [ 2.955951] Enter PCE micro-code init [ 2.959913] Exit PCE micro-code init [ 2.963144] Switch API: PCE MicroCode loaded !! [ 2.967773] ::::::: SWAPI Reached :::::: [ 2.971625] GSWIP devid = 1 [ 2.974445] memres->start = 0x1a000000 memres->end = 0x1a002fff [ 2.980387] addr_gswr = 0xba000000 [ 2.983727] drivers/net/ethernet/lantiq/switch-api/gsw_init.c:ltq_gsw_api_register:963 (Register r base:0xba000000) [ 2.994142] [ 2.994142] ########## Switch Core INIT for device = 1 ########## [ 3.001662] Switch Core Base Address = 0xba000000 [ 3.006381] [ 3.006381] GSWIP 3.0 HardWare Capability [ 3.011816] ----------------------------- [ 3.011816] [ 3.017315] Switch Version ID = 0x30 [ 3.022239] [ 3.023732] Number of logical port = 2 [ 3.028398] Number of ports including V port = 17 [ 3.033225] Number of queues = 32 [ 3.037947] Number of meter instance = 64 [ 3.042748] Number of shapers = 32 [ 3.047495] Number of PMAC = 1 [ 3.052190] Number of CPU PORT = 0 [ 3.056903] [ 3.058347] PPPOE table size = 16 [ 3.063145] IP packet length table size = 16 [ 3.067895] Protocol table size = 32 [ 3.072713] MAC DA/SA table size = 64 [ 3.077444] Application table size = 64 [ 3.082225] IP DA/SA MSB table size = 64 [ 3.087019] IP DA/SA LSB table size = 64 [ 3.091768] Multicast table size = 64 [ 3.096574] Multicast Hw Snoop = 0 [ 3.101230] TFLOW table size = 512 [ 3.106116] MAC bridge table size = 2048 [ 3.111040] TFLOW RMON counter table Size = 256 [ 3.115932] Payload Table Size = 64 [ 3.120675] Extend VLAN Table Size table = 0 [ 3.125387] VlanFilter table Size = 0 [ 3.125387] [ 3.131524] [ 3.133059] Enter PCE micro-code init [ 3.137006] Exit PCE micro-code init [ 3.140207] Switch API: PCE MicroCode loaded !! [ 3.153506] grx500wdt 12000000.watchdog: [grx500wdt_probe]:[280] cpu_clk=600000000 [ 3.159627] grx500wdt 12000000.watchdog: [grx500wdt_probe]WDT reset is Bit31, RCU_IAP_WDT_RST_STAT=0x60000408 [ 3.169583] grx500wdt 12000000.watchdog: [grx500wdt_probe]Not WDT reset. [ 3.176260] grx500_wdt: [Enable_WDT_intr]:[121] irq= 225 cpu = 0 [ 3.182203] grx500wdt 12000000.watchdog: [grx500wdt_probe]:[348] grx500_wdt = 681df098 [ 3.190483] grx500_wdt: [Enable_WDT_intr]:[121] irq= 225 cpu = 1 [ 3.196159] grx500wdt 12000000.watchdog: [grx500wdt_probe]:[348] grx500_wdt = 681eb098 [ 3.204229] grx500_wdt: [Enable_WDT_intr]:[121] irq= 225 cpu = 2 [ 3.209974] grx500wdt 12000000.watchdog: [grx500wdt_probe]:[348] grx500_wdt = 681f7098 [ 3.218132] grx500wdt 12000000.watchdog: H/w Watchdog Timer: (max 7) (nowayout= 0) [ 3.227011] of: dev_pm_opp_of_cpumask_add_table: failed to get cpu3 device [ 3.232978] thermal thermal_zone0: binding zone cpu-thermal with cdev thermal-cpufreq-0 failed:-22 [ 3.244648] NET: Registered protocol family 10 [ 3.249319] NET: Registered protocol family 17 [ 3.252618] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 3.265293] 8021q: 802.1Q VLAN Support v1.8 [ 3.274262] ubi0: attaching mtd5 [ 3.885306] ubi0: scanning is finished [ 3.918185] ubi0: attached mtd5 (name "system_sw", size 122 MiB) [ 3.922785] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 3.929582] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 3.936373] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 3.943324] ubi0: good PEBs: 975, bad PEBs: 1, corrupted PEBs: 0 [ 3.949288] ubi0: user volume: 5, internal volumes: 1, max. volumes count: 128 [ 3.956520] ubi0: max/mean erase counter: 44/22, WL threshold: 4096, image sequence number: 1317713037 [ 3.965814] ubi0: available PEBs: 532, total reserved PEBs: 443, PEBs reserved for bad PEB handling: 19 [ 3.975209] ubi0: background thread "ubi_bgt0d" started, PID 413 [ 3.983101] clk: Not disabling u[ 3.993850] RAMDISK: squashfs filesystem found at block 0 [ 3.997797] RAMDISK: Loading 6368KiB [1 disk] into ram disk... done. [ 4.242338] VFS: Mounted root (squashfs filesystem) readonly on device 1:0. [ 4.253009] Freeing unused kernel: 1300k freed [ 4.255991] This architecture does not have kernel memory protection. [ 4.923734] init: Console is alive [ 5.786927] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 5.836552] SCSI subsystem initialized [ 5.843035] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 5.852902] init: - preinit - [ 6.465924] random: jshn: uninitialized urandom read (4 bytes read) [ 6.541257] random: jshn: uninitialized urandom read (4 bytes read) ls: /lib/modules/4.9.109/ltq_atm*: No such file or directory [ 6.606237] random: jshn: uninitialized urandom read (4 bytes read) [ 6.732633] UBIFS (ubi0:7): background thread "ubifs_bgt0_7" started, PID 500 [ 6.874293] UBIFS (ubi0:7): recovery needed [ 7.341273] UBIFS (ubi0:7): recovery completed [ 7.344467] UBIFS (ubi0:7): UBIFS: mounted UBI device 0, volume 7, name "rootfs_data" [ 7.352073] UBIFS (ubi0:7): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 7.362033] UBIFS (ubi0:7): FS size: 30220288 bytes (28 MiB, 238 LEBs), journal size 1523712 bytes (1 MiB, 12 LEBs) [ 7.372404] UBIFS (ubi0:7): reserved for root: 1427378 bytes (1393 KiB) [ 7.379004] UBIFS (ubi0:7): media format: w4/r0 (latest is w4/r0), UUID 880B951B-DE2B-46B7-8805-025E32EA09C6, small LPT model [ 7.462773] UBIFS (ubi0:7): un-mount UBI device 0 [ 7.466042] UBIFS (ubi0:7): background thread "ubifs_bgt0_7" stops [ 7.583052] UBIFS (ubi0:7): background thread "ubifs_bgt0_7" started, PID 508 [ 7.854531] UBIFS (ubi0:7): UBIFS: mounted UBI device 0, volume 7, name "rootfs_data" [ 7.860914] UBIFS (ubi0:7): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 7.870848] UBIFS (ubi0:7): FS size: 30220288 bytes (28 MiB, 238 LEBs), journal size 1523712 bytes (1 MiB, 12 LEBs) [ 7.881248] UBIFS (ubi0:7): reserved for root: 1427378 bytes (1393 KiB) [ 7.887838] UBIFS (ubi0:7): media format: w4/r0 (latest is w4/r0), UUID 880B951B-DE2B-46B7-8805-025E32EA09C6, small LPT model [ 7.903508] mount_root: switching to ubifs overlay [ 7.918653] urandom-seed: Seed file not found (/etc/urandom.seed) [ 8.070291] procd: - early - [ 8.715335] procd: - ubus - [ 8.767462] urandom_read: 3 callbacks suppressed [ 8.767474] random: ubusd: uninitialized urandom read (4 bytes read) [ 8.777564] random: ubusd: uninitialized urandom read (4 bytes read) [ 8.783485] random: ubusd: uninitialized urandom read (4 bytes read) [ 8.792648] procd: - init - [ 9.101940] kmodloader: loading kernel modules from /etc/modules.d/* [ 9.138400] IFXOS, Version 1.6.9 (c) Copyright 2009, Lantiq Deutschland GmbH [ 9.153470] Netfilter messages via NETLINK v0.30. [ 9.159137] ip_set: protocol 6 [ 9.208937] u32 classifier [ 9.210196] input device check on [ 9.213884] Actions configured [ 9.219805] Mirror/redirect action on [ 9.225041] GACT probability on [ 9.261033] fuse init (API version 7.26) [ 9.270925] Bridge firewalling registered [ 9.274833] cpuload module initialised ! [ 9.286409] ip_tables: (C) 2000-2006 Netfilter Core Team [ 9.292771] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 9.314614] nf_conntrack version 0.5.0 (3072 buckets, 12288 max) [ 9.411431] ctnetlink v0.93: registering with nfnetlink. [ 9.420690] nf_conntrack_rtsp v0.7 loading [ 9.590548] nf_nat_rtsp v0.7 loading [ 9.621431] PPA Stack Adaptation layer Loaded... [ 9.629568] phy-xrx500 phy-xrx500: requesting ltq_fw_PHY11G_IP_xRx5xx_A21.bin [ 9.695206] phy-xrx500 phy-xrx500: booting GPHY0 firmware at 2DA00000 for GRX500 [ 9.825340] xt_time: kernel timezone is -0000 [ 9.837205] PMAC_EG_CFG_SET for GSW-L [ 9.839603] PMAC_IG_CFG_SET for GSW-L [ 9.843185] PMAC_EG_CFG_SET for GSW-R [ 9.850029] PMAC_IG_CFG_SET for GSW-R [ 9.852514] [ 9.852514] GSW PMAC Init Done!!! [ 9.857185] registering one of MII bus [ 9.861089] libphy: lantiq,xrx500-mdio: probed [ 9.903726] registering PAE MII bus [ 9.905954] libphy: lantiq,xrx500-mdio-pae: probed [ 9.912263] [datapath_proc] { dp_sub_proc_install_30 : 3566 }dp_sub_proc_install ok [ 9.918524] Rmon clear for CTP RX/TX --Logical Port 0 [ 9.923511] Rmon clear for CTP RX/TX --Logical Port 1 [ 9.928515] Rmon clear for CTP RX/TX --Logical Port 2 [ 9.933585] Rmon clear for CTP RX/TX --Logical Port 3 [ 9.938585] Rmon clear for CTP RX/TX --Logical Port 4 [ 9.943653] Rmon clear for CTP RX/TX --Logical Port 5 [ 9.948654] Rmon clear for CTP RX/TX --Logical Port 6 [ 9.953720] Rmon clear for CTP RX/TX --Logical Port 0 [ 9.958724] Rmon clear for CTP RX/TX --Logical Port 1 [ 9.963797] Rmon clear for CTP RX/TX --Logical Port 2 [ 9.968794] Rmon clear for CTP RX/TX --Logical Port 3 [ 9.973853] Rmon clear for CTP RX/TX --Logical Port 4 [ 9.978864] Rmon clear for CTP RX/TX --Logical Port 5 [ 9.983943] Rmon clear for CTP RX/TX --Logical Port 6 [ 9.988934] Rmon clear for CTP RX/TX --Logical Port 7 [ 9.993993] Rmon clear for CTP RX/TX --Logical Port 8 [ 9.999003] Rmon clear for CTP RX/TX --Logical Port 9 [ 10.004069] Rmon clear for CTP RX/TX --Logical Port 10 [ 10.009160] Rmon clear for CTP RX/TX --Logical Port 11 [ 10.014306] Rmon clear for CTP RX/TX --Logical Port 12 [ 10.019403] Rmon clear for CTP RX/TX --Logical Port 13 [ 10.024556] Rmon clear for CTP RX/TX --Logical Port 14 [ 10.029647] Rmon clear for CTP RX/TX --Logical Port 15 [ 10.034793] Rmon clear for CTP RX/TX --Logical Port 16 [ 10.039916] [datapath_api] { dp_init_module : 2667 }datapath init done [ 10.046471] [cbm] { dp_port_alloc : 2853 }flags 0x2 [ 10.051275] [cbm] { cbm_add_to_list : 250 }2 [ 10.055554] [cbm] { dp_port_alloc : 3001 }disabling q 16 port 6 [ 10.061431] [cbm] { dp_port_alloc : 3007 }first time LOOKUP prgrm [ 10.067944] [cbm] { dp_port_alloc : 3012 }1024 [ 10.072096] no interface attached to this interface! [ 10.076971] xrx500_of_iface: rx csum offload is enabled ! [ 10.082317] [cbm] { dp_enable : 3317 }ep=1 tmu_port=6 queue=16 sid=0 [ 10.088684] [cbm] { dp_enable : 3357 }enable queue 16 [ 10.093629] [cbm] { dp_enable : 3358 }flag 1 refcnt 1024 [ 10.100574] [cbm] { dp_port_alloc : 2853 }flags 0x2 [ 10.104083] [cbm] { cbm_add_to_list : 250 }2 [ 10.108304] [cbm] { dp_port_alloc : 3001 }disabling q 17 port 7 [ 10.114309] [cbm] { dp_port_alloc : 3007 }first time LOOKUP prgrm [ 10.120783] [cbm] { dp_port_alloc : 3012 }1024 [ 10.125154] xrx500_of_iface: rx csum offload is enabled ! [ 10.130135] trying to connect: eth0_1 to device: 0:02 with irq: 260 [ 10.272147] eth0_1: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:02, irq=260) [ 10.289739] [cbm] { dp_enable : 3317 }ep=2 tmu_port=7 queue=17 sid=1 [ 10.294670] [cbm] { dp_enable : 3357 }enable queue 17 [ 10.299648] [cbm] { dp_enable : 3358 }flag 1 refcnt 1024 [ 10.306586] Lantiq ethernet driver for XRX500 init. [ 10.367686] Genconf offset correct [ 10.393679] Min TC:1 Max TC:4 [ 10.395207] [fw_vmb_get_irq]:[1546] CPU = 3 IRQ = 110 !!! [ 10.400688] VMB-FW-IPI : 85 [ 10.405640] MpeDebugRespRegIrq : 226 [ 10.409088] [vmb_tc_alloc]:[1046] CPU tct tc_status = 1 [ 10.414320] [fw_vmb_get_irq]:[1546] CPU = 3 IRQ = 110 !!! [ 10.419688] VMB-FW-IPI : 85 [ 10.424491] mpe_hal_to_vmb_callback_hdlr not support status 0x0 [ 10.432284] [vmb_cpu_start]:[951] vmb_fw_msg_t = a0000218 cpu = 3 ! [ 10.437148] [vmb_cpu_start]:[966] start_address = 2814935040 cpu = 3 !!!! [ 10.443966] [gic_trigger]:[645] VMB_CPU_IPI3 - 85 CPU = 3 O ts.de WAIT gvt IcI interrupt t1]lWAnch f om pu 0O MSG_>D_= 01akeup_vpe = 0 ! [ 10.465581] [fw_vmb_ipi3_hdlr]:[203] CPU = 0 irq = 8 [ 10.469082] [fw_vmb_ipi3_hdlr]:[211] cid = 1, vid = 1 [ 10.474120] [fw_vmb_ipi3_hdlr]:[248] [ 10.477675] [fw_vmb_ipi3_hdlr]:[250] [ 10.481245] vmb_wq = 627e22e0 [ 10.484814] [vmb_cpu_start]:[1000] OUTSIDE wakeup_vpe = 1 vpet->fw_vmb.status = 1 [ 10.491835] [vmb_cpu_start]:[1006] ret = 1 [ 10.496000] CPU TMU resources for MPE are Port:3 ,SB:20, Q:36 [ 10.504595] MPE HAL Run FW success . [ 10.507916] MPE Proc Creation....!!! [ 10.531442] TMU HAL Init. [ 10.532694] [cbm] { reserved_ports_highest : 4770 }26 26 25 41 [ 10.538415] Total node : 544 and size of each node: 3192 [ 10.543817] Total allocated size=1736448 [ 10.554445] Total node : 544 and size of each node: 3192 [ 10.566235] Number of CPU TMU Ports are:1 [ 10.569815] CPU TMU resources are Port:2 ,SB:19, Q:35 [ 10.575951] Number of MPE TMU Ports are:1 [ 10.580924] MPE TMU resources are Port:3 ,SB:20, Q:36 [ 10.587578] TMU HAL Create Proc entries [ 10.590955] Done!! [ 10.645274] PPA API --- init successfully [ 10.656038] Lantiq directpath datapath driver for XRX500, version lantiq_directpath_drv_xrx500.c:v1.1.1 [ 10.656038] ,(c)2009 Lantiq AG [ 10.667666] kmodloader: done loading kernel modules from /etc/modules.d/* [ 13.232751] grx500_wdt: grx500wdt_set_timeout: timeout = 7, cpu = 1, id = 1 PERCPUID = 1 [ 13.437044] cdcs_DD: module license 'NetComm Wireless Proprietary' taints kernel. [ 13.443172] Disabling lock debugging due to kernel taint [ 13.449841] Start cdcsDD [ 13.450991] [T51]trace_alloc:367: global init [ 13.455383] [T51]trace_alloc:374: tracer 'dd_write' created [ 13.460877] [T51]trace_alloc:374: tracer 'dd_read' created [ 13.466438] [T51]trace_alloc:374: tracer 'dd_notify' created [ 13.471969] [T51]trace_alloc:374: tracer 'dd_malloc' created [ 13.662407] random: crng init done [ 13.664367] random: 1 urandom warning(s) missed due to ratelimiting [ 14.318778] Init Success [ 14.319902] [ltq_mpe_hal_drv] { mpe_hal_generic_hook : 551 }ppa_hal_generic_hook not support cmd 0xd [ 14.329071] [ltq_mpe_hal_drv] { mpe_hal_generic_hook : 551 }ppa_hal_generic_hook not support cmd 0xd [ 14.339097] directpath start id: 0, end id: 272 [ 14.342729] Installed the ppa learning netfilter hooks [ 14.347748] ppa_init - init succeeded [ 15.858088] p2p channel turned ON ! [ 15.860132] [datapath_api] { dp_rx_enable : 2498 }Dummy dp_rx_enable, need to implement later [ 15.995158] NComm TMS V6.81 Kernel Module loaded. [ 17.077299] ubi0 error: ubi_open_volume: cannot open device 0, volume 7, error -16 VRX168 Startup - config file: /opt/intel/bin/vrx618_startup_cfg.sh VRX618 setup - net setup net setup skipped due to uboot variable labnet_usage=[parameter labnet_usage is not existed] Device 1bef:0030 found Device 8086:09aa found [ 17.751649] VRX618 PCI EP Driver, Version 0.4.1 [ 17.754912] (c) Copyright 2016, Intel Deutschland GmbH [ 17.760023] drv_vrx618_ep_init - use PCIe Vendor=8086, Device=0x09AA [ 17.766548] drv_vrx618_ep_probe - enter [ 17.770270] pci 0002:00:00.0: enabling device (0000 -> 0003) [ 17.775990] vrx618_ep 0002:01:00.0: enabling device (0000 -> 0002) [ 17.782024] platform_device_pmi_setup - enter [ 17.786388] pmi_platform_data_set_v2 - enter [ 17.790578] pmi_platform_data_set_v2 - register PMI Platform device [ 17.796989] PMI Dev: phy_addr=0xBC000000 phy_mem_size__byte=8388608 (0x800000) [ 17.804415] virt_addr=0xFC000000 irq=0 [ 17.809153] pci_vendor_id=0x8086 pci_device_id=0x09AA [ 17.815296] platform_device_pmi_setup - register PMI platform device [ 17.821904] platform_device_datapath_setup - enter [ 17.826430] dp_platform_data_set_v2 - enter [ 17.830510] dp_platform_data_set_v2 - register Datapath Platform device [ 17.837281] PMI Dev: phy_addr=0xBC000000 phy_mem_size__byte=8388608 (0x800000) [ 17.844744] virt_addr=0xFC000000 irq=n/a [ 17.849610] pci_vendor_id=0x8086 pci_device_id=0x09AA [ 17.855786] platform_device_datapath_setup - register datapath platform device [ 17.889369] DSL PMI Driver, Version 0.6.1.1. [ 17.892206] (c) Copyright 2016, Intel Deutschland GmbH [ 17.898216] PMI[--]: pmi_platform_probe (v2) - Platform Data: vrx618_pmi [ 17.904047] struct_size=48, pci_vendor_id=0x8086, pci_device_id=0x9AA [ 17.910506] phy_addr=0xBC000000, phy_mem_size__byte=0x800000, virt_addr=0xFC000000, irq=0 FIO_DSL_PMI_DRV_CONFIG_SET: dev[00]: pmi_result=0 [ 18.004618] PMI[00]: fcsi_lc_pll_reset - exec (startup=1) FIO_DSL_PMI_DEV_CONFIG_SET: dev[00]: pmi_result=0 FIO_DSL_PMI_DRV_DEBUGLEVEL_SET: dev[00]: pmi_result=0 Unknow model, using VRX619 firmware VRX618 setup - skip DTI PMI Start VRX618 setup - FW Download CPE [ 18.565688] Download - selected devices = 0x00000001 (deselect = 0x00000000) [ 18.571301] PMI[00]: dev_reset - DP[0] (shutdown) cfg state set failed (ret=-1063, dp_ret=0) [ 19.002536] PMI[00]: fcsi_lc_pll_reset - exec (startup=0) [ 19.402538] PMI[00]: evt distribute - discard, no listen user (msgid = 0x0200, TAN = 0x08F0, RET = 0xDEAD, LEN = 0x0008). [ 19.412047] PMI[00]: evt_modem_ready, result=0x0000, DL state=3, Dev state=5 - goto operation. [ 19.420674] PMI[00]: evt distribute - discard, no listen user (msgid = 0x02FF, TAN = 0x09F0, RET = 0xDEAD, LEN = 0x0002). [ 19.432551] download - done, selected = 0x00000001 FIO_DSL_PMI_DEV_FW_DOWNLOAD: dev[00]: pmi_result=0 VRX618 setup - load datapath driver (release setup). [ 19.498444] VRX618 Driver DataPath, Version 0.4.2 [ 19.501775] (c) Copyright 2017, Intel Deutschland GmbH [ 19.507785] DSL_DP(dp_platform_data_get_v2) - Platform Data (Vers V2): aca_datapath [ 19.514671] struct_size=44, vers_cntrl=0x2X [ 19.518873] pci_vendor_id=0x8086, pci_device_id=0x9AA [ 19.524042] phy_addr=0xBC000000, phy_mem_size__byte=0x800000, virt_addr=0xFC000000 [ 19.531639] ==> DSL_DP: drv_dsl_dp_init__dev_cfg() - enter [ 19.537176] ==> DSL_DP: drv_dsl_dp_cfg_startup() - enter [ 19.542408] ==> DSL_DP: cfg_state_set_startup() - enter [ 19.547641] ==> DSL_DP: cfg_state_set_startup__init() - enter [ 19.553359] ==> DSL_DP: cfg_state_set_startup_tc__init() - enter [ 19.560849] DevOp cfg state - plat_ctx[0]: cfg_state=5 tc_mode=1 (retval=1) [ 19.566439] ==> DSL_DP: drv_dsl_dp_cfg_startup() - enter [ 19.571646] ==> DSL_DP: cfg_state_set_startup() - enter [ 19.576889] ==> DSL_DP: cfg_state_set_startup__init() - enter [ 19.582612] ==> DSL_DP: cfg_state_set_startup_tc__init() - enter [ 19.588570] ==> DSL_DP: cfg_state_set_startup() - enter [ 19.593850] ==> DSL_DP: cfg_state_set_startup__const() - enter [ 19.599605] ==> DSL_DP: ctx_setup__global_cfg_init() - enter [ 19.605275] ==> DSL_DP: ctx_setup__hif_const_init() - enter [ 19.610803] DSL_DP(ctx_setup__hif_const_init): [ 19.615267] soc_cfg TXIN: byte_swap=1, host_desc_num=32, pd_size_in_dw=2 [ 19.622182] soc_cfg TXOUT: byte_swap=1, host_desc_num=32, pd_size_in_dw=2 [ 19.629185] soc_cfg RXIN: byte_swap=1, host_desc_num=32, pd_size_in_dw=1 [ 19.636009] soc_cfg RXOUT: byte_swap=1, host_desc_num=32, pd_size_in_dw=2 [ 19.642952] ==> DSL_DP: cfg_state_set_startup_tc__const() - enter [ 19.648998] ==> DSL_DP: ctx_setup__pmac_cfg_init() - enter [ 19.654500] ==> DSL_DP: pmac_setup__cfg_egress_set() - enter [ 19.660109] ==> DSL_DP: pmac_setup__cfg_egress_set() - enter [ 19.665791] ==> DSL_DP: pmac_setup__cfg_egress_set() - enter [ 19.666010] PMI[00]: evt distribute - discard, no listen user (msgid = 0x0200, TAN = 0x0AF0, RET = 0xDEAD, LEN = 0x0008). [ 19.682375] ==> DSL_DP: pmac_setup__cfg_igress_set() - enter [ 19.688045] ==> DSL_DP: pmac_setup__cfg_igress_set() - enter [ 19.693670] ==> DSL_DP: pmac_setup__cfg_igress_set() - enter [ 19.699272] ==> DSL_DP: pmac_setup__cfg_igress_set() - enter [ 19.704933] ==> DSL_DP: pmac_setup__cfg_igress_set() - enter [ 19.710590] ==> DSL_DP: pmac_setup__cfg_igress_set() - enter [ 19.716247] ==> DSL_DP: pmac_setup__cfg_igress_set() - enter [ 19.721840] ==> DSL_DP: pmac_setup__cfg_igress_set() - enter [ 19.727544] ==> DSL_DP: pmac_setup__cfg_igress_set() - enter [ 19.733189] ==> DSL_DP: pmac_setup__cfg_igress_set() - enter [ 19.738757] ==> DSL_DP: pmac_setup__cfg_igress_set() - enter [ 19.744429] ==> DSL_DP: pmac_setup__cfg_igress_set() - enter [ 19.750034] ==> DSL_DP: pmac_setup__cfg_igress_set() - enter [ 19.755749] ==> DSL_DP: cfg_state_set_startup() - enter [ 19.760887] ==> DSL_DP: cfg_state_set_startup__dynamic() - enter [ 19.766911] ==> DSL_DP: drv_dsl_dp_aca_fw_setup() - enter [ 19.772266] ==> DSL_DP: dsl_dp_fw_file_load() - enter [ 19.808712] ==> DSL_DP: aca_fw_init__img_hdr_get() - enter [ 19.812806] ==> DSL_DP: aca_fw_init__img_hdr_v1_get() - enter [ 19.818474] ==> DSL_DP: aca_fw_init__fw_parse() - enter [ 19.823716] ==> DSL_DP: fw_parse__reg_section() - enter [ 19.828896] DSL_DP(fw_parse__reg_section) - Sec_ID=0x00000001, len=1, p_fw_sec_base=0x0000001C [ 19.837516] ==> DSL_DP: fw_parse__reg_section() - enter [ 19.842736] DSL_DP(fw_parse__reg_section) - Sec_ID=0x00000002, len=2, p_fw_sec_base=0x0000002C [ 19.851286] ==> DSL_DP: fw_parse__reg_section() - enter [ 19.856536] DSL_DP(fw_parse__reg_section) - Sec_ID=0x00000003, len=3, p_fw_sec_base=0x00000044 [ 19.865116] ==> DSL_DP: fw_parse__sram_desc() - enter [ 19.870123] ==> DSL_DP: fw_parse__sram_desc() - enter [ 19.875188] ==> DSL_DP: fw_parse__sram_desc() - enter [ 19.880194] ==> DSL_DP: fw_parse__sram_desc() - enter [ 19.885264] ==> DSL_DP: fw_parse__sram_desc() - enter [ 19.890264] ==> DSL_DP: fw_parse__sram_desc() - enter [ 19.895343] ==> DSL_DP: fw_parse__sram_desc() - enter [ 19.900334] ==> DSL_DP: fw_parse__sram_desc() - enter [ 19.905417] ==> DSL_DP: fw_parse__dma() - enter [ 19.909884] ==> DSL_DP: fw_parse__host_init() - enter [ 19.914963] ==> DSL_DP: fw_parse__fw_section() - enter [ 19.920044] ==> DSL_DP: dplib_setup__rx_buf_alloc() - enter [ 19.927148] ==> DSL_DP: dplib_setup__dp_port_alloc() - enter [ 19.931353] [cbm] { dp_port_alloc : 2853 }flags 0x18 [ 19.936404] [cbm] { cbm_add_to_list : 250 }1 [ 19.940555] [cbm] { dp_port_alloc : 3001 }disabling q 32 port 4 [ 19.946517] [cbm] { dp_port_alloc : 3007 }first time LOOKUP prgrm [ 19.952961] [cbm] { dp_port_alloc : 3012 }1024 [ 19.957217] ==> DSL_DP: dplib_setup__umt_port_alloc() - enter [ 19.962769] DSL_DP(dplib_setup__umt_port_alloc): cbm_get_wlan_umt_pid(port_id=7) [ 19.970086] DSL_DP(dplib_setup__umt_port_alloc): ep_id=0, cbm_id=0, p_umt->id=0, dma_ctrlid=1, dma_cid=7 [ 19.979573] ==> DSL_DP: dplib_setup__dma_port_alloc() - enter [ 19.985287] DSL_DP(dplib_setup__dma_port_alloc): ltq_request_dma(dma_chan=0x1000007, name=dsl_gfast_drv_dp) [ 19.995024] DSL_DP(dplib_setup__dma_port_alloc): ltq_dma_chan_desc_alloc(dma_chan=0x1000007, ds_dnum=1024) [ 20.004836] DSL_DP(dplib_setup__dma_port_alloc): ltq_dma_chan_off(dma_chan=0x1000007) [ 20.012497] ==> DSL_DP: cfg_state_set_startup_tc__dynamic() - enter [ 20.018674] ==> DSL_DP: dplib_setup__datapath_register() - enter [ 20.024708] DSL_DP(dplib_setup__datapath_register): ctx_setup - dp_register_dev_ext(inst=0, dp_id=7) - register [ 20.034763] ==> DSL_DP: dplib_setup__netdev_create() - enter [ 20.042548] ==> DSL_DP: dplib_setup__pmac_cfg_set() - enter [ 20.046690] ==> DSL_DP: pmac_setup__cfg_igress_set() - enter [ 20.052979] ==> DSL_DP: dplib_setup__cbm_resource_get() - enter [ 20.058247] DSL_DP(dplib_setup__cbm_resource_get): p_plat_ctx->port_id=7 [ 20.064991] cbm_buf_free_base=0xBE7D4080, num_free_entries=32, num_deq_ports=1 [ 20.072206] port_no=4, cbm_dq_port_base=0xBE7D4100, num_desc=32 [ 20.078270] DSL_DP(dplib_setup__cbm_resource_get): p_plat_ctx->port_id=7, p_dma->chan=7 [ 20.086234] txin: dbase=0x1E7D4100 dnum=32, hd_size_in_dw=4 [ 20.091915] txout: dbase=0x1E7D4080 dnum=32, hd_size_in_dw=1 [ 20.097677] rxin: dbase=0x27DC8000 dnum=1024, hd_size_in_dw=1 [ 20.103579] rxout: dbase=0x27DC8000 dnum=1024, hd_size_in_dw=4 [ 20.109442] ==> DSL_DP: dsl_dp_aca_hif_setup() - enter [ 20.114602] ==> DSL_DP: cfg_state_set_startup() - enter [ 20.119771] ==> DSL_DP: cfg_state_set_startup__write() - enter [ 20.125619] ==> DSL_DP: dp_write__osccfg_check() - enter [ 20.130876] ==> DSL_DP: hw_write__apr_setup() - enter [ 20.135949] ==> DSL_DP: dsl_dp_aca_hw_write_aca_fw_prepare() - enter [ 20.142260] ==> DSL_DP: aca_hw_write__fw_mem_clear() - enter [ 20.148008] ==> DSL_DP: aca_hw_write__sram_clear() - enter [ 20.153640] ==> DSL_DP: dsl_dp_aca_hw_write_dma_init() - enter [ 20.159198] ==> DSL_DP: aca_dma_init__cntl() - enter [ 20.164162] ==> DSL_DP: aca_dma_init__port() - enter [ 20.169090] ==> DSL_DP: aca_dma_init__desc_list_clear() - enter [ 20.175011] DSL_DP(aca_dma_init__desc_list_clear): p_fw_info->chan_num=8) [ 20.181759] ch_id=0x0, dbase=0xBC000000 + 0x0014E000, dlen=8 [ 20.187544] ch_id=0x1, dbase=0xBC000000 + 0x0014E008, dlen=8 [ 20.193248] ch_id=0x2, dbase=0xBC000000 + 0x0014E010, dlen=8 [ 20.198936] ch_id=0x3, dbase=0xBC000000 + 0x0014E018, dlen=8 [ 20.204730] ch_id=0x4, dbase=0xBC000000 + 0x0014E030, dlen=8 [ 20.210398] ch_id=0x5, dbase=0xBC000000 + 0x0014E038, dlen=8 [ 20.216175] ch_id=0x6, dbase=0xBC000000 + 0x0014E020, dlen=8 [ 20.221854] ch_id=0x7, dbase=0xBC000000 + 0x0014E028, dlen=8 [ 20.227668] ==> DSL_DP: aca_dma_init__channel() - enter [ 20.232838] DSL_DP(aca_dma_init__channel): p_fw_info->chan_num=8) [ 20.238893] ch_id=0x0, dbase=0xBC000000 + 0x0014E000, dlen=1 [ 20.244636] ch_id=0x1, dbase=0xBC000000 + 0x0014E008, dlen=1 [ 20.250345] ch_id=0x2, dbase=0xBC000000 + 0x0014E010, dlen=1 [ 20.256095] ch_id=0x3, dbase=0xBC000000 + 0x0014E018, dlen=1 [ 20.261808] ch_id=0x4, dbase=0xBC000000 + 0x0014E030, dlen=1 [ 20.267599] ch_id=0x5, dbase=0xBC000000 + 0x0014E038, dlen=1 [ 20.273294] ch_id=0x6, dbase=0xBC000000 + 0x0014E020, dlen=1 [ 20.278981] ch_id=0x7, dbase=0xBC000000 + 0x0014E028, dlen=1 [ 20.284782] ==> DSL_DP: dsl_dp_aca_hw_write_aca_fw() - enter [ 20.290343] ==> DSL_DP: aca_hw_write__setup_hif() - enter [ 20.295819] ==> DSL_DP: aca_hw_write__setup_hif_soc() - enter [ 20.301465] ==> DSL_DP: aca_hw_write__fw_regs() - enter [ 20.306723] ==> DSL_DP: aca_hw_write__setup_mac_ht() - enter [ 20.312315] ==> DSL_DP: aca_hw_write__fw_regs() - enter [ 20.317595] ==> DSL_DP: aca_hw_write__setup_genrisc() - enter [ 20.323295] ==> DSL_DP: aca_hw_write__fw_regs() - enter [ 20.328459] ==> DSL_DP: aca_hw_write_xbar_ia__reject_clr() - enter [ 20.334648] ==> DSL_DP: aca_hw_write_xbar_ia__reject_clr() - enter [ 20.340787] ==> DSL_DP: aca_hw_write__fw_section() - enter [ 20.346990] ==> DSL_DP: aca_hw_write__hif() - enter [ 20.351106] ==> DSL_DP: dsl_dp_aca_hw_write_hif_rx_buf() - enter [ 20.357213] ==> DSL_DP: aca_hw_write__hif_rx_buf_list() - enter [ 20.363066] DSL_DP(aca_hw_write__hif_rx_buf_list): Data - (0x29B00000 0x29B00800 0x29B01000 ...) [ 20.371779] ==> DSL_DP: cfg_state_set_startup_tc__write() - enter [ 20.377914] ==> DSL_DP: cfg_state_set_startup() - enter [ 20.383090] ==> DSL_DP: cfg_state_set_startup__dev_start() - enter [ 20.389218] ==> DSL_DP: dsl_dp_aca_device_stop() - b_rst=0, target_mask=0xF [ 20.396206] ==> DSL_DP: dsl_dp_aca_device_start() - enter [ 20.401540] ==> DSL_DP: aca_start__magic_check() - enter [ 20.406874] ==> DSL_DP: cfg_state_set_startup_tc__dev_start() - enter [ 20.413305] ==> DSL_DP: dplib_setup__umt_start() - enter [ 20.418588] DSL_DP(dplib_setup__umt_start): ltq_dma_chan_on(dma_chan=0x1000007) [ 20.425898] DSL_DP(dplib_setup__umt_start): ltq_umt_enable(p_umt->id=0, p_plat_ctx->port_id=7, 1) [ 20.434756] ==> DSL_DP: cfg_state_set_startup() - enter [ 20.439919] ==> DSL_DP: cfg_state_set_startup__dev_run() - enter [ 20.445943] ==> DSL_DP: dsl_dp_aca_device_magic_get() - enter [ 20.451922] ==> DSL_DP: cfg_state_set_startup_tc__dev_run() - enter [ 21.293085] LTM fwd Device is NULL for ptm0[ 21.297069] device ptm0 entered promiscuous mode [ 21.300382] NComm Ethernet 802.1AG OA&M: protocols handlers loaded:ptm0. Unknow model, using VRX619 firmware VRX618 setup - load dsl-daemon. DSL: start DSL daemon. DSL: using firmware file - /lib/firmware/09AA/xcpe_fw.bin DSL: using device mask - 0x00000001 DSL: Device granularity is 1 DSL: No 2nd firmware pointer DSL: FW version 12.3.2.1.0.51 DSL: Given warmstart memory will be analyzed... DSL: using external memory DSL: ...Warmstart m[ 21.881966] ==> DSL_DP: dp_fct_cb_dp_op() - enter [ 21.886498] ==> DSL_DP: drv_dsl_dp_shared_line_showtime_cfg() - enter [ 21.892861] ==> DSL_DP: drv_dsl_dp_line_cfg_showtime_set() - enter [ 21.898983] ==> DSL_DP: dp_line_cfg_showtime_exit__ptm() - enter [ 21.905017] DSL_DP(dp_line_cfg_showtime_exit__ptm): line_num=0, net_dev_cfg_state=0 [ 21.912640] DSL_DP(dp_line_cfg_showtime_exit__ptm): line_info[0].line_state=0 [ 21.919728] DSL_DP(dp_line_cfg_showtime_exit__ptm): line_info[1].line_state=0 emory not initialized DSL: ...Startup mode: COLDSTART DSL: device setup start with device mask 0x0001 DSL_ORN_DeviceOpen - msg device for CMD/ACK handling opened succesfully DSL_ORN_DeviceOpen - msg device for EVT handling opened succesfully DSL: device setup comp[ 21.951440] Download - selected devices = 0x00000001 (deselect = 0x00000000) [ 21.957731] ==> DSL_DP: dp_fct_cb_dp_op() - enter [ 21.962360] ==> DSL_DP: drv_dsl_dp_shared_cfg_state() - enter [ 21.968116] ==> DSL_DP: drv_dsl_dp_cfg_shutdown() - enter [ 21.973499] ==> DSL_DP: cfg_state_set_shutdown() - enter [ 21.978757] ==> DSL_DP: cfg_state_set_shutdown__dev_run() - enter [ 21.984860] ==> DSL_DP: cfg_state_set_shutdown_tc__dev_run() - enter [ 21.991173] ==> DSL_DP: dp_line_cfg_showtime_exit__ptm() - enter [ 21.997235] DSL_DP(dp_line_cfg_showtime_exit__ptm): line_num=0, net_dev_cfg_state=0 [ 22.004835] DSL_DP(dp_line_cfg_showtime_exit__ptm): line_info[0].line_state=0 [ 22.011918] DSL_DP(dp_line_cfg_showtime_exit__ptm): line_info[1].line_state=0 [ 22.019105] ==> DSL_DP: dp_line_cfg_showtime_exit__ptm() - enter [ 22.025082] DSL_DP(dp_line_cfg_showtime_exit__ptm): line_num=1, net_dev_cfg_state=0 [ 22.032745] DSL_DP(dp_line_cfg_showtime_exit__ptm): line_info[0].line_state=0 [ 22.039786] DSL_DP(dp_line_cfg_showtime_exit__ptm): line_info[1].line_state=0 [ 22.046947] ==> DSL_DP: dsl_dp_aca_op_cntrl_stop_hw_us() - enter [ 22.052942] ==> DSL_DP: dsl_dp_aca_op_cntrl_stop_hw_ds() - enter [ 22.058891] DSL_DP(dsl_dp_aca_op_cntrl_stop_hw_ds): reset sequence pending (DMA1SL_P0_CTRL1=0xFFFFFFFF) [ 22.068307] ==> DSL_DP: dsl_dp_aca_device_hd_cnt_get() - enter [ 22.074131] ==> DSL_DP: dsl_dp_aca_device_stop() - b_rst=0, target_mask=0xF [ 22.081022] ==> DSL_DP: cfg_state_set_shutdown() - enter [ 22.086348] ==> DSL_DP: cfg_state_set_shutdown__dev_start() - enter [ 22.092614] ==> DSL_DP: cfg_state_set_shutdown_tc__dev_start() - enter [ 22.099073] ==> DSL_DP: dplib_setup__umt_stop() - enter [ 22.104326] DSL_DP(dplib_setup__umt_stop): ltq_umt_enable(p_umt->id=0, p_plat_ctx->port_id=7, 0) [ 22.113099] DSL_DP(dplib_setup__umt_stop): ltq_dma_chan_off(dma_chan=0x1000007) [ 22.120350] ==> DSL_DP: dsl_dp_aca_device_stop() - b_rst=1, target_mask=0xF [ 22.127323] ==> DSL_DP: aca_dma_stop__choff() - enter [ 22.132360] ==> DSL_DP: aca_hw_write_xbar_ia__reject_set() - enter [ 22.138544] ==> DSL_DP: aca_hw_write_xbar_ia__reject_set() - enter [ 22.144689] ==> DSL_DP: aca_device_stop__sw_reset() - enter [ 22.150205] ==> DSL_DP: dsl_dp_aca_device_xbar_shutdown() - enter [ 22.156321] ==> DSL_DP: aca_hw_write_xbar_ia__reset() - enter leted with device mask 0x0001 DSL: device driver: DSL PMI Driver, Version 0.6.1.1. DSL[00]: do FW download [ 22.343871] DSL_DP(aca_hw_write_xbar_ia__reset): ACA XBAR IA[4] - reset activation failed (status=0x1) [ 22.351707] ==> DSL_DP: aca_hw_write_xbar_ia__reset() - enter [ 22.539437] DSL_DP(aca_hw_write_xbar_ia__reset): ACA XBAR IA[6] - reset activation failed (status=0x1) [ 22.547301] ==> DSL_DP: cfg_state_set_shutdown() - enter [ 22.552608] ==> DSL_DP: cfg_state_set_shutdown__write() - enter [ 22.558471] ==> DSL_DP: cfg_state_set_shutdown_tc__write() - enter [ 22.564672] ==> DSL_DP: cfg_state_set_shutdown() - enter [ 22.569931] ==> DSL_DP: cfg_state_set_shutdown__dynamic() - enter [ 22.576051] ==> DSL_DP: cfg_state_set_shutdown_tc__dynamic() - enter [ 22.582353] ==> DSL_DP: dplib_setup__netdev_release() - enter check for API start [ 22.932651] device ptm0 left promiscuous mode [ 22.935574] NComm Ethernet 802.1AG OA&M: protocols handlers unloaded:ptm0. [ 23.202555] ==> DSL_DP: dplib_setup__datapath_unregister() - enter [ 23.207283] DSL_DP(dplib_setup__datapath_unregister): dp_register_dev_ext(inst=0, dp_id=7) - deregister [ 23.216728] ==> DSL_DP: dplib_setup__dma_port_release() - enter [ 23.222844] ==> DSL_DP: dplib_setup__umt_port_release() - enter [ 23.228459] ==> DSL_DP: dplib_setup__dp_port_release() - enter [ 23.234448] ==> DSL_DP: dplib_setup__rx_buf_free() - enter [ 23.239783] ==> DSL_DP: drv_dsl_dp_aca_fw_release() - enter [ 23.245347] ==> DSL_DP: dsl_dp_fw_file_release() - enter [ 23.250616] ==> DSL_DP: cfg_state_set_shutdown() - enter [ 23.255995] ==> DSL_DP: cfg_state_set_shutdown__const() - enter [ 23.261791] ==> DSL_DP: cfg_state_set_shutdown_tc__const() - enter [ 23.268024] ==> DSL_DP: ctx_setup__hif_const_reset() - enter [ 23.273641] ==> DSL_DP: ctx_setup__global_cfg_reset() - enter [ 23.732538] PMI[00]: fcsi_lc_pll_reset - exec (startup=0) [ 24.112560] PMI[00]: evt_modem_ready, result=0x0000, DL state=3, Dev state=5 - goto operation. [ 24.122509] download - done, selected = 0x00000001 DSL[00]: FW DL - FW download successful DSL: FW version 12.3.2.1.0.51 DSL: DSL: ***************************************************** DSL: DSL library version: 5.3.31 DSL: ***************************************************** DSL: Max number of devices : 1 DSL: Max number of lines : 1 DSL: Max number of lines/device : 1 DSL: Number of channels/line : 1 DSL: DSL: Memory usage of warm start resistent data base DSL: magic key data base : 4 bytes DSL: profile config data base : 7952 bytes DSL: instance config data base : 44 bytes DSL: device config data base : 64 bytes DSL: global array config data base: 4 bytes DSL: line config data base : 532 bytes DSL: channel config data base : 48 bytes DSL: line array config data base : 888 bytes DSL: -------------- DSL: Total : 9536 bytes DSL: DSL: Memory usage of status data base DSL: global array status data base: 4 bytes DSL: device status data base : 24 bytes DSL: line status data base : 1036 bytes DSL: channel status data base : 636 bytes DSL: -------------- DSL: Total : 1700 bytes DSL: DSL: Context memory usage DSL: context structure : 19328 bytes DSL: Timeout event lists : 576 bytes DSL: firmware binary : 1492436 bytes DSL: -------------- DSL: Total : 1511764 bytes DSL: Memory usage of Performance Management (PM) DSL: channel endpoints : 4 : 18208 bytes DSL: datapath endpoints: 4 : 41856 bytes DSL: line endpoints: 2 : 67584 bytes DSL: -------------- DSL: Total : 142080 bytes DSL: ***************************************************** DSL: DSL_Init finished with device mask 0x0001 DSL: IPC Server ServerInit DSL: IPC Server ServerInit SUCCESS API completely started (after 2 s) Check if FW has been downloaded FW has been downloaded (after 0 s) setup CPE line (setup_cntrl=1 --> DSL API). nReturn=0 DSL_APILibraryVersion="5.3.31" DSL_ChipSetFWVersion="12.3.2.1.0.51;1.0.1.6.6" DSL_ChipSetHWVersion="VRX619" DSL_ChipSetType="ORION" DSL_DriverVersion="DSL PMI Driver, Version 0.6.1.1." nHybridType=0 nReturn=0 nReturn=0 nReturn=0 nLine=0 nReturn=0 nReturn=0 nLine=0 nChannel=0 nReturn=0 nLine=0 nChannel=0 nReturn=0 nLine=0 nReturn=0 nReturn=0 nReturn=0 DSL[00]: FAIL [ 24.779810] ==> DSL_DP: dp_fct_cb_dp_op() - enter [ 24.784300] ==> DSL_DP: drv_dsl_dp_shared_line_showtime_cfg() - enter [ 24.790625] ==> DSL_DP: drv_dsl_dp_line_cfg_showtime_set() - enter [ 24.796863] DSL_DP(drv_dsl_dp_line_cfg_showtime_set) - invalid state = 0 [ 24.803543] DSL DP CP: showtime cfg - status set failed (pcie_if_num=0, line_num=0) DSL[00]: Error during DP showtime exit! (-2402) DSL[00]: FAIL [ 24.852624] ==> DSL_DP: dp_fct_cb_dp_op() - enter [ 24.855874] ==> DSL_DP: drv_dsl_dp_shared_line_showtime_cfg() - enter [ 24.862301] ==> DSL_DP: drv_dsl_dp_line_cfg_showtime_set() - enter [ 24.868544] DSL_DP(drv_dsl_dp_line_cfg_showtime_set) - invalid state = 0 [ 24.875253] DSL DP CP: showtime cfg - status set failed (pcie_if_num=0, line_num=0) DSL[00]: Error during DP showtime exit! (-2402) DSL[00]: DSL_ORN_ApplicabilityCheck applicability 0x00000102F3010000 on MsgId 0x8904 DSL[00]: DSL_ORN_ApplicabilityCheck applicability 0x00000102F3010000 on MsgId 0x8904 not suitable for current state 0x1! not suitable for current state 0x1! SubError Code 0x00, FW Fail Code 0x0197 Debug Codes: 0x7E65 0x000A 0x0000 0x7E65 0x0014 0x0000 0x0000 0x0000 DSL[00]: IDLE DSL[00]: IDLE nReturn=0 DSL[00]: IDLE nReturn=0 DSL[00]: IDLE DSL[00]: IDLE DSL[00]: Msg Denied for MsgID=0x8851 (FwErrorCode=0xFFFF) - on try 0! Break. DSL[00]: Error for send CMD MsgID=0x8851, Recovery Trigger 0x0! nReturn=0 ==> VRX618 Datapath: setup CPE side GSW_REGISTER_SET GSW_REGISTER_SET GSW_REGISTER_SET GSW_REGISTER_SET GSW_REGISTER_SET GSW_REGISTER_SET GSW_PMAC_GLBL_CFG_SET GSW_REGISTER_SET GSW_PMAC_GLBL_CFG_SET keep ripd DSL[00]: READY DSL[00]: DSL_ORN_ApplicabilityCheck applicability 0x0000010083010000 on MsgId 0x0F10 not suitable for current state 0x200! PM_LN[00][NE]: Failed to retrieve CurrLineExecCounters! PM_LN[00][NE]: Failed to QueryCounters!